Discovering Plumbing Basics is Essential for Installing a Bathtub
Discovering Plumbing Basics is Essential for Installing a Bathtub
Blog Article
We have noticed the article relating to How to Install a Bathtub directly below on the web and felt it made sense to write about it with you on this site.
Mounting a tub isn't exactly rocket science, however it does require strong plumbing, woodworking, as well as in some cases, tiling abilities. Replacing an old bathtub with a new one is also a reasonably hard task. If the old tub is easily available, the job can relocate immediately; if you have to open up a wall to remove the old tub and also position the brand-new tub, the job is a lot harder. In either situation, the task is within a home handyman's skills, although you will require a helper to leave the old tub as well as embeded in the new one. Make sure you have actually qualified on your own for the job as well as fit trying it. Rather than hiring a contractor to take over a halfway-completed job, it is far better to take into consideration employing one prior to you start. Possibilities are you may need a professional plumber to make tube connections.
This post will assist you set up a brand-new bathtub in your washroom if you have already acquired a new bathtub as well as do not need to change the arrangement of your previous water supply pipelines.
Your tools and also material checklist should consist of the following:
Removing Old Touches
If you require to change old taps with new ones as a part of your installment, after that the first thing you need to do is separate the water. After doing so, switch on the faucets to drain any water remaining in the system. The process of removing the existing taps can be rather bothersome because of the restricted access that is commonly the instance.
Make use of a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that links the supply pipelines to the taps. Have a towel ready for the remaining water that will certainly originate from the pipes. As soon as the supply pipes have actually been removed, use the exact same tool to loosen up the nut that holds the taps onto the bath/basin. You will need to stop the solitary taps from transforming during this procedure. When the taps have been gotten rid of, the holes in the bath/basin will certainly have to be cleaned up of any kind of old securing substance.
Prior to proceeding to fit the brand-new faucets, compare the pipeline links on the old taps to the new faucets. If the old taps are longer than the brand-new taps, then a shank adapter is needed for the new taps to fit.
Fitting New Touches
If the tails of the new faucets are plastic, after that you will require a plastic adapter to avoid damages to the thread. One end of the connector fits on the plastic tail of the tap as well as the various other end provides a link to the existing supply pipelines.
If you require to fit a monobloc, then you will call for reducing couplers, which attaches the 10mm pipeline of the monobloc to the typical 15mm supply pipe.
Next, place the faucet in the installing opening in the bath/basin making sure that the washers are in place between the faucet and also the sink. Safeguard the tap in position with the manufacturer provided backnut. As soon as the faucet is safely in position, the supply pipes can be attached to the tails of the taps. The taps can either be connected by using corrugated copper piping or with normal tap ports. The previous kind needs to be linked to the faucet finishes first, tightening up only by hand. The supply pipes can later on be attached to the other end. Tighten both ends with a spanner after both ends have been attached.
Setting up the Bath tub
Utilizing the two wooden boards under its feet, put the bath tub in the required placement. The wood boards are handy in equally spreading the weight of the bathtub over the area of the boards as opposed to focusing all the weight onto 4 little factors.
The following objective is to ensure that the tub is leveled all round. This can be attained by inspecting the spirit level and changing the feet on the tub till the spirit level reads degree.
To set up taps, fit the bottom of the outermost versatile faucet adapter to the proper supply pipeline by making a compression sign up with; after that do the very same for the other tap.
Switch on the water supply and check all joints as well as brand-new pipework for leaks as well as tighten them if needed. Load the bath tub and likewise examine the overflow electrical outlet and the normal electrical outlet for leakages.
Lastly, deal with the bath paneling as explained in the producer's instruction manual. Tiling as well as sealing around the bath tub ought to wait until the bath tub has been utilized at the very least when as this will certainly settle it right into its last position.
Preparing for the Setup
Firstly, the supporting structure provided with the bathroom needs to be fitted (if called for) according to the maker's instructions. Next, fit the taps or mixer to the bathtub. When fitting the tap block, it is essential to ensure that if the faucet comes with a plastic washing machine, it is fitted in between the bath and also the taps. On a plastic bath, it is also reasonable to fit a sustaining plate under the taps device to avoid strain on the tub.
Fit the adaptable tap adapters to the bottom of the two faucets utilizing 2 nuts and olives (sometimes provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the electrical outlet through the hole in the bath. Make use of the nut provided by the producer to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the flexible overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bath. Make certain you make use of every one of the supplied washing machines.
Link the catch to the bottom of the waste outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Connect all-time low of the overflow tube in a comparable manner.The bath should now prepare to be fitted in its final placement.
Tiling Around the Tub
In the location where the bath satisfies the floor tile, it is essential to secure the accompanies a silicone rubber caulking. This is essential as the fitting can move sufficient to break a rigid seal, triggering the water to pass through the wall surface between the bath and also the tiling, leading to problems with dampness as well as feasible leakages to the ceiling listed below.
You can select from a range of coloured sealants to blend in your fixtures and also installations. They are offered in tubes and cartridges, and also are capable of sealing gaps approximately a size of 3mm (1/8 inch). If you have a bigger void to fill, you can load it with spins of drenched newspaper or soft rope. Remember to always fill the tub with water before sealing, to permit the movement experienced when the tub is in usage. The sealant can fracture rather early if you do not think about this movement before sealing.
Alternatively, ceramic coving or quadrant tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are additionally easily readily available on the marketplace. It is suggested to fit the floor tiles using water-resistant or water resistant adhesive and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I'm certainly very serious about How to Install a Bathtub and I am praying you liked the entire blog entry. Sharing is caring. Helping people is fun. Thanks for taking the time to read it.
Pipe issues? Connect. Report this page